Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
This post down below about How to Install a Bathtub Yourself is relatively compelling. Check it out for your own benefit and decide what you think about it.
Mounting a tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a new one is also a moderately tough project. If the old bathtub is readily obtainable, the job can relocate immediately; if you have to open a wall surface to remove the old tub and also place the brand-new bathtub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually qualified on your own for the job and are comfortable trying it. As opposed to hiring a specialist to take over a halfway-completed task, it is much better to take into consideration utilizing one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This post will assist you mount a new tub in your bathroom if you have currently acquired a brand-new tub as well as do not require to alter the setup of your previous water supply pipes.
Your tools and product list ought to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain any water remaining in the system. The process of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is typically the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipes. When the supply pipes have been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing substance.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines are in place in between the tap and the sink. Protect the tap in place with the producer given backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type ought to be linked to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Using the two wooden boards under its feet, position the tub in the required placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 little points.
The next objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub until the level reviews level.
To mount faucets, fit all-time low of the furthest versatile tap connector to the suitable supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the water supply and also check all joints and also brand-new pipework for leaks as well as tighten them if essential. Load the bathtub as well as likewise examine the overflow outlet and also the regular electrical outlet for leaks.
Lastly, repair the bathroom paneling as explained in the supplier's user's manual. Tiling and sealing around the bathtub needs to wait until the bath tub has actually been made use of a minimum of once as this will certainly resolve it into its final setting.
Planning for the Installment
First of all, the sustaining structure supplied with the bath should be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the area where the bath meets the tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture an inflexible seal, causing the water to permeate the wall surface in between the bathroom as well as the tiling, bring about complications with dampness and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and also fittings. They are marketed in tubes and also cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can split rather very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is recommended to fit the tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that post about How to Install a Bathtub while surfing the internet. Enjoyed our content? Please share it. Help another person locate it. Thank-you for your time invested reading it.
Further Details Report this page